Loading…
Member
I used 3M tape I got from the auto parts store. Just give the section a wipe with IPA, peel a corner or side of the tape and smooth it out as you go. Hit it with a hair drier to get the air bubbles out and ensure a good…
I looked at the bike online and it appears to have fender mounts. I run Planet Bike fenders and they're okay. PDW fenders would work better as the stays are longer. If you don't want to go through the hassle try the SKS…
More information like what bike would help. Fender are notoriously a pain to install and take time and a bit of customizing to get right.
Alex Boondocks 3. Comes in 650b and 700c. Comes with adapter for different axles sizes. Relatively light, look not too bad too.
Zurichman wrote: You didn't say if you were running tubes or tubeless big difference. I am running tubeless. Everybody IMHO has to find their sweet spot or at least what their comfort level is. At my end running…
I'm 200lbs and ride pretty much 30psi front and 32psi rear all the time with Gravelking SK's 650bx1.9's. On my enduro bike I'm running 20psi front and 21psi rear with Maxxis DHF 2.6 front and DHR 2.4 rear. I'm in the…
Here you go. Raceface clones. I can't remember who, I think it was Seth's Bike Hacks, did a comparison and while they are similar on the outside they do have different internals. You can't go wrong for 30 bucks though.…
I've signed up for the 60 day free trial until I can find something else as easy to route plan with, otherwise the free version is just fine for me.
So I got my set of Gravelking SK + tires and here are my impressions. These tires are replacing a set of WTB Byway tires which I really like but wanted more traction for loose conditions. I first mounted these tires…
The dart is great.
This is to tighten the axle? I've been 3d printing and modeling for quite a while and I can tell you for certain that no FDM or resin 3d printer can produce anything strong enough to get the axle to torque specs. Better…
Why not something like a XC race tire like the Maxxis Pace? https://www.maxxis.com/catalog/tire-482-140-pace Or the Crossmark2? https://www.maxxis.com/catalog/tire-505-140-crossmark-ii Both come in 2.1
I think it's only on the mech version not the Di2 as far as I see. I don't know. I have the 600 levers and I don't ever feel like there's a loss of power. My Enduro bike is quite a bit heavier with Servo wave and I…
Shimano GRX 800 and 600 series are both 11 speed. GRX 400 is 10spd. The difference between 800 and 600 is the 800/810 has Servo wave for increased power when braking.
I'm interested in these as well as they're the only ones available to me. How are they for suppleness as well?
I don't thing Stan's and Tufo are the same company. I believe it's a latex based sealant like Stan's but as you say, made for tubulars. Perhaps it's not recommended to put into tires because it dries too quickly.…
I've used Orange Seal and I thought it was great. I'm running Stan's regular with glitter and so far so good. No big Stan's boogers yet. If I had to choose between the two I'd go with Orange Seal. If you use the Finish…
I'm in the same boat. I think I may order the Planet Bike fenders as the PDW ones are too spendy for me.
I'm using a Geosmina top tube bag that I've adapted to be bolt on. I've seen DIY on YouTube using a piece of plastic but it seemed to not be sturdy enough. I whipped up a baseplate in Fusion 360 and 3d printed it.…
Min here in Canada, Ride for Water, has been postponed until October.